TOUGH STUFF AC5900 ACRYLIC ROOF COATING MATERIAL SAFETY DATA SHEET

The conditions or methods of handling, storage, use and disposal of the product are beyond our control, and may be beyond our knowledge. FOR THIS AND OTHER REASONS, WE DO NOT ASSUME RESPONSIBILITY AND EXPRESSLY DISCLAIM LIABILITY FOR LOSS, DAMAGE, OR EXPENSE ARISING OUT OF OR IN ANY WAY CONNECTED WITH THE HANDLING, STORAGE, USE, OR DISPOSAL OF THE PRODUCT.

This MSDS was prepared and is to be used only for this product. If apprised of changes, updated MSDS sheets will be promptly issued. Users must make their own determination regarding the suitability of the product for their own purpose prior to use.

VIEW / DOWNLOAD (Windows - "Right Click", Mac - "Option-Click") a printable PDF version of this document.

I - MATERIAL IDENTIFICATION AND INFORMATION
II - PHYSICAL/CHEMICAL CHARACTERISTICS
III - FIRE AND EXPLOSION DATA
IV - REACTIVITY HAZARD DATA
V - HEALTH HAZARD DATA
VI - CONTROL AND PROTECTIVE MEASURES
VII - PRECAUTIONS FOR SAFE HANDLING AND USE/LEAKS
RELATED DOCUMENTS

SECTION I - MATERIAL IDENTIFICATION AND INFORMATION

Components - Chemical Name & Common Names
(Hazardous Components 1% or greater: Carcinogens 0.1% or greater)

CHEMICAL NAME (COMMON NAME)	CAS #	%	OSHA PEL (PPM)	ACGIH TLV (PPM)	OTHER LIMITS RECOMMENDED
Acrylic Latex mixture		100
Defoamer mixture		0.1
Surfactant mixture		0.2
Propylene Glycol	57-55-6	0.2		L - 2.5 U - 12.5
Texanol	25265-77-4	0.4
Tio2	13463-67-7	.6-.12
Calcium Carbonate	1317-65-3	20-30
Wallastanite	No CAS	.8-10
Fungicide		.0002

SECTION II - PHYSICAL/CHEMICAL CHARACTERISTICS

1) BOILING POINT	212°F / 100°C
2) SPECIFIC GRAVITY (H2O = 1)	1.18
3) VAPOR PRESSURE	N/A
4) MELTING POINT	N/A
5) VAPOR DENSITY (Air=1)	Heavier than air
6) EVAPORATION RATE	slower
7) SOLUBILITY IN WATER	N/A
8) WATER REACTIVE	N/A
9) APPEARANCE & COLOR	White thick paste-acrylic odor

SECTION III - FIRE AND EXPLOSION DATA

1) FLASH POINT & METHOD:

None

2) AUTO-IGNITION TEMPERATURE:

N/A

3) FLAMMABILITY LIMITS IN AIR % BY VOLUME:

LEL: N/A

UEL: N/A

4) EXTINGUISHER (MEDIA):

Water & foam - all types

5) SPECIAL FIRE FIGHTING PROCEDURES:

N/A

6) UNUSUAL FIRE AND EXPLOSION HAZARDS:

N/A

SECTION IV - REACTIVITY HAZARD DATA

1) STABILITY:

Stable

2) CONDITIONS TO AVOID:

Freezing

3) INCOMPATIBILITY (Materials to Avoid):

Strong acids

4) HAZARDOUS DECOMPOSITION PRODUCTS:

Fires may cause decomposition that may produce carbon monoxides, nitrogen oxides or carbon dioxide. These are highly toxic.

5) HAZARDOUS POLYMERIZATION:

Will not occur

SECTION V - HEALTH HAZARD DATA

1) PRIMARY ROUTES OF ENTRY:

1. Inhalation- yes
2. Skin absorption- yes
3. Ingestion- yes

2) CARCINOGEN LISTED IN:

1. NTP - No
2. IARC MONOGRAPH - No
3. OSHA - No

3) HEALTH HAZARDS

ACUTE: N/A

CHRONIC: N/A

4) SIGNS AND SYMPTOMS OF EXPOSURE:

Eyes: May cause burning
Ingestion: May cause irritation to throat & mouth and abdominal irritation
Skin: None known
Inhalation: None known

5) MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE:

N/A

6) EMERGENCY FIRST AID PROCEDURES:

Seek medical assistance for further treatment, observation and support if necessary.

7) EYE CONTACT:

Flush with water for 15 minutes, obtain medical attention if irritation persists.

8) SKIN CONTACT:

Remove contaminated clothing and wash skin with soap & water.

9) INHALATION:

Remove to fresh air.

10) INGESTION:

Give at least 2 glasses of water. Induce vomiting if patient is conscious.

SECTION VI - CONTROL AND PROTECTIVE MEASURES

1) RESPIRATORY PROTECTION (Specify type):

For spraying - use an approved nostril and mouth chemical cartridge mask in areas that are not well ventilated. In ventilated areas, use a formed cloth mask.

2) PROTECTIVE GLOVES:

Rubber

3) EYE PROTECTION:

Goggles

4) VENTILATION TO BE USED:

Local exhaust N/A
Mechanical (general): N/A

5) OTHER (Specify):

N/A

SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE/LEAKS

1) STEPS TO BE TAKEN IF MATERIAL IS SPILLED OR RELEASED:

Small spills should be flushed with soapy water. Large spills should be diked and collected for disposal.

2) WASTE DISPOSAL METHODS:

The solids can be precipitated using alum and acids. The solids can be landfilled. The liquids can be flushed to a sanitary sewer.

3) ENVIRONMENTAL IMPACT:

None

4) PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE:

None.

Revised March 2001


FOR ADDITIONAL INFORMATION, GO TO:

• AC5900 Product Data Information
  

VIEW A DIFFERENT TOUGH STUFF PRODUCT Choose.... Tough Stuff | Product Index ---ACRYLICS--- AC5000 AC5000 MSDS AC5500 Mastic AC5500 Mastic MSDS AC5600 AC5600 MSDS AC5900 AC5900 MSDS ---CLEANER--- CL404 CL404 MSDS ---ADDITIVES--- D200 D200 MSDS D210 D210 MSDS ---FABRIC--- FA200 Information ---PRIMERS--- PR3800 PR3800 MSDS ---URETHANES--- UR1600 UR1600 MSDS UR1650 Mastic UR1650 Mastic MSDS UR1900 UR1900 MSDS UR2550 UR2550 Part A MSDS UR2550 Part B MSDS UR2650 UR2650 Part A MSDS UR2650 Part B MSDS UR2750 UR2750 Part A MSDS UR2750 Part B MSDS

See also: