ST7200 WATER BASED MASONRY AND BRICK STAIN PRODUCT DATA

Tough Stuff Masonry & Brick Stain provides a long lasting maintenance free coating to color and protect masonry without disturbing the natural texture.

VIEW / DOWNLOAD (Windows - "Right Click", Mac - "Option-Click") a printable PDF version of this document.

PRODUCT CHARACTERISTICS
APPLICATION CONDITIONS
APPLICATION PROCEDURES
PERFORMANCE TIPS
CLEANUP INSTRUCTIONS
SAFETY PRECAUTIONS
ORDERING INFORMATION

RELATED DOCUMENTS

PRODUCT CHARACTERISTICS

EXCELLENT COLOR RETENTION: Pure organic oxide pigments and premix acrylic copolymers give Tough Stuff Stains excellent long term color retention.
DEEP PENETRATION: Fast and deep penetration is achieved through advanced micro pigment technology. The resulting stain is locked into the masonry and can not peel or flake like paint or conventional coatings.
NON-OXIDIZING: Tough Stuff stains use the most advanced formulation technology available to resist oxidation beyond that of conventional coatings.
NON LAPPING AND EASY TOUCH-UP: The unique makeup of this product allows it to chemically dissolve and blend into itself during application. Excellent for areas exposed to graffiti such as highway bridges.
FAST DRYING: Simple application and super fast drying even in cold temperatures allows the applicator to apply the second coat before moving the stage setup. This greatly reduces application costs and gets the job done ahead of schedule.

ECONOMICAL AND COST EFFECTIVE: Excellent coverage rates and simple application give the Tough Stuff system an edge over even flat latex on rough surfaces for both price and appearance. Initial costs can pay back three-fold on the long term maintenance-free performance of Tough Stuff stains.

PROPERTY	VALUE
Solids by Weight	49%
Solids by Volume	38%
Dry Time (75°F/24°C)	20-30 minutes
Cure Time (75°F/24°C)	4 hours
Gloss (60°F/16°C )	10 – 15
Weight per gallon	10.83 lbs.
Shelf Life	Unlimited in unopened container
Storage	Do not store material at temperatures less than 40°F/4°C or above 120°F/49°C.

APPLICATION CONDITIONS

PROPERTY	MIN.	MAX.
Temperature:
Air & Surface	No Min.	100°F
Material	No Min.	95°F
Relative Humidity:		95%

Do not apply when the dew point is less than 5°F above ambient temperature.

APPLICATION PROCEDURES

GENERAL

Do not open container until ready to use.
Always apply Tough Stuff Stains in two separate applications. The first coat will penetrate and saturate the surface to form a color base. The second coat is applied perpendicular to the first coat to achieve color uniformity. Coarse surfaces such as split face and fluted block may require a third coat to achieve uniform color and sheen.

SURFACE PREPARATION

All surfaces must be clean. fully dry and completely cured. They must be free from dust, curing agents, form release agents, efflorescence, scale or any foreign substances that may interfere with adhesion.
* Previous coatings should be completely removed to ensure adequate penetration.
Hard or glazed surfaces such as dense or glazed brick or smooth concrete must be sweep blasted or acid etched to allow for adequate surface penetration.
Tough Stuff stain can be applied over existing coatings providing the two coatings are compatible. A test area must be applied to ensure compatibility.
Always contact the Coatings International, Inc. technical department for recommendations when the ability of the stain to penetrate the substrate is in question.

MIXING

Material shall be mixed for a minimum of four (4) minutes prior to application. Use an air operated or explosion proof mixer with a blade capable of uniformly mixing the entire container.

SPRAY APPLICATIONS

Spray the first coat in a uniform horizontal direction followed by a uniform overlapping vertical direction as soon as the first coat has dried.
The spray gun should be held not more than 18” from the wall. Rough surfaces such as fluted block will require care to ensure that all angles are covered.
Applicator should first test an inconspicuous area to best determine the proper absorption rates to achieve best color uniformity.
A standard airless type capable of handling 2000 psi and at least one gallon per minute is required for best results.
A reversible self-cleaning spray tip with an orifice size of .013” to .017” and a minimum 40° fan angle is recommended.

BRUSHING OR ROLLING

When brushing or rolling, care should be taken to ensure that the same coverage rate as the spraying is used. Different coverage rates will result in color variation.

ESTIMATED COVERAGE RATES

SUBSTRATE TOTAL SQ. FT./GAL.

Concrete — Cast in Place* 150

Concrete — Precast* 150

Concrete Block — Standard# 100

Concrete Block — Lightweight# 50

Concrete Block — Split Faced# 50

Concrete Block — Fluted# 50

Concrete Block — Brick# 50

Stucco — Sprayed On# 50

Stucco — Troweled# 100

Notes:
* — Apply approximately 1/2 the total number of gallons on the first coat. Use remainder on second coat.

# — Apply approximately 2/3 the total number of gallons on the first application and the remaining 1/3 on the second application.

The above coverage rates are for estimating purposes only. Absorption rates will vary depending on the porosity of the substrate. Always allow for extra surface area when estimating fluted, raked and split faced surfaces.

APPLICATION TIPS

Due to inventory fluctuations there may be times when different batch numbers are delivered to fill a single order. It is the contractors responsibility to make sure that the same batch number is applied to the same side of the building or that the material is boxed together to insure even coverage and appearance. It is highly recommended to apply a sample on an inconspicuous area of the building prior to estimating the job to determine the best absorption rate and suitability of the application. Written approval should be obtained from the architect or the building owner prior to proceeding with the project.

PERFORMANCE TIPS

WATERPROOFING: Superior penetrating clear silicone rubber sealant is recommended to thoroughly saturate the surface to form an excellent water shed over the stain. This greatly extends the life of both the coating and the substrate.

CLEANUP INSTRUCTIONS

Clean equipment with mineral spirits. The lines of the spray equipment should be flushed thoroughly..

SAFETY PRECAUTIONS

INSTALLERS must read, understand and follow all technical and informational literature for Tough Stuff Masonry and Brick Stain prior to using this product.
For chemical emergencies, spills, leaks, exposure, or accidents in the US: CALL CHEMTREC 24 HOURS A DAY / 365 DAYS A YEAR 1-800-424-9300.

ORDERING INFORMATION

CONTAINER	WEIGHT	CLASS
5 gallon (19 liter) pail	55 pounds	55
55 gallon (209 liter) drum	616 pounds	55

Published technical data and instructions are subject to change without notice. Please contact your Coatings International representative for the most current information.

Revised May 2001

FOR ADDITIONAL INFORMATION, GO TO: